Monthly Archives: May 2017

Arduino and Raspberry Pi working together. Part 2 (now with i2c)

The easiest way to connect our Arduino board to our Raspberry Py is using the USB cable, but sometimes this communication is a nightmare, especially because there isn’t any clock signal to synchronize our devices and we must rely on the bitrate. There’re different ways to connect our Arduino and our Raspberry Py such as I2C, SPI and serial over GPIO. Today we’re going to speak about I2C, especially because it’s pretty straightforward if we take care with a couple of things. Let’s start.

I2C uses two lines SDA (data) and SCL (clock), in addition to GND (ground). SDA is bidirectional so we need to ensure, in one way or another, who is sending data (master or slave). With I2C only master can start communications and also master controls the clock signal. Each device has a 7bit direction so we can connect 128 devices to the same bus.

If we want to connect Arduino board and Raspberry Pi we must ensure that Raspberry Pi is the master. That’s because Arduino works with 5V and Raspberry Pi with 3.3V. That means that we need to use pull-up resistors if we don’t want destroy our Raspberry Pi. But Raspberry Pi has 1k8 ohms resistors to the 3.3 votl power rail, so we can connect both devices (if we connect other i2c devices to the bus they must have their pull-up resistors removed)

Thats all we need to connect our Raspberry pi to our Arduino board.

  • RPi SDA to Arduino analog 4
  • RPi SCL to Arduino analog 5
  • RPi GND to Arduino GND

Now we are going to build a simple prototype. Raspberry Pi will blink one led (GPIO17) each second and also will send a message (via I2C) to Arduino to blink another led. That’s the Python part

import RPi.GPIO as gpio
import smbus
import time
import sys

bus = smbus.SMBus(1)
address = 0x04

def main():
    gpio.setmode(gpio.BCM)
    gpio.setup(17, gpio.OUT)
    status = False
    while 1:
        gpio.output(17, status)
        status = not status
        bus.write_byte(address, 1 if status else 0)
        print "Arduino answer to RPI:", bus.read_byte(address)
        time.sleep(1)


if __name__ == '__main__':
    try:
        main()
    except KeyboardInterrupt:
        print 'Interrupted'
        gpio.cleanup()
        sys.exit(0)

And finally the Arduino program. Arduino also answers to Raspberry Pi with the value that it’s been sent, and Raspberry Pi will log the answer within console.

#include <Wire.h>

#define SLAVE_ADDRESS 0x04
#define LED  13

int number = 0;

void setup() {
  pinMode(LED, OUTPUT);
  Serial.begin(9600);
  Wire.begin(SLAVE_ADDRESS);
  Wire.onReceive(receiveData);
  Wire.onRequest(sendData);

  Serial.println("Ready!");
}

void loop() {
  delay(100);
}

void receiveData(int byteCount) {
  Serial.print("receiveData");
  while (Wire.available()) {
    number = Wire.read();
    Serial.print("data received: ");
    Serial.println(number);

    if (number == 1) {
      Serial.println(" LED ON");
      digitalWrite(LED, HIGH);
    } else {
      Serial.println(" LED OFF");
      digitalWrite(LED, LOW);
    }
  }
}

void sendData() {
  Wire.write(number);
}

Hardware:

  • Arduino UNO
  • Raspberry Pi
  • Two LEDs and two resistors

Code available in my github

Arduino and Raspberry Pi working together

Basically everything we can do with Arduino it can be done also with a Raspberry Pi (an viceversa). There’re things that they’re easy to do with Arduino (connect sensors for example). But another things (such as work with REST servers, databases, …) are “complicated” with Arduino and C++ (they are possible but require a lot of low level operations) and pretty straightforward with Raspberry Pi and Python (at least for me and because of my background)

With this small project I want to use an Arduino board and Raspberry Pi working together. The idea is blink two LEDs. One (green one) will be controlled by Raspberry Pi directly via GPIO and another one (red one) will be controlled by Arduino board. Raspberry Pi will be the “brain” of the project and will tell to Arduino board when turn on/off it’s led. Let’s show you the code.

import RPi.GPIO as gpio
import serial
import time
import sys
import os

def main():
    gpio.setmode(gpio.BOARD)
    gpio.setup(12, gpio.OUT)

    s = serial.Serial('/dev/ttyACM0', 9600)
    status = False

    while 1:
        gpio.output(12, status)
        status = not status
        print status
        s.write("1\n" if status else "0\n")
        time.sleep(1)

if __name__ == '__main__':
    try:
        main()
    except KeyboardInterrupt:
        print 'Interrupted'
        gpio.cleanup()
        try:
            sys.exit(0)
        except SystemExit:
            os._exit(0)

As we can see the script is a simple loop and blink led (using pin 12) with one interval of one second. Our Arduino board is connected directly to the Raspberry Pi via USB cable and we send commands via serial interface.

Finally the Arduino program:

#define LED  11

String serialData = "";
boolean onSerialRead = false; 

void setup() {
  // initialize serial:
  Serial.begin(9600);
  serialData.reserve(200);
}

void procesSerialData() {
  Serial.print("Data " + serialData);
  if (serialData == "1") {    
    Serial.println(" LED ON");
    digitalWrite(LED, HIGH);
  } else {
    Serial.println(" LED OFF");
    digitalWrite(LED, LOW);
  }
  serialData = "";
  onSerialRead = false;
}

void loop() {
  if (onSerialRead) {
    procesSerialData();
  }
}

void serialEvent() {
  while (Serial.available()) {
    char inChar = (char)Serial.read();
    if (inChar == '\n') {
      onSerialRead = true;
    } else {
      serialData += inChar;
    }
  }
}

Here our Arduino Board is listening to serial interface (with serialEvent) and each time we receive “\n” the main loop will turn on/off the led depending on value (1 – On, 0 – Off)

We can use I2C and another ways to connect Arduino and Raspberry Pi but in this example we’re using the simplest way to do it: A USB cable. We only need a A/B USB cable. We don’t need any other extra hardware (such as resistors) and the software part is pretty straightforward also.

Hardware:

  • Arduino UNO
  • Raspberry Pi 3
  • Two LEDs and two resistors

Code in my github account