Monthly Archives: June 2017

Playing with Raspberry Pi, Arduino, NodeMcu and MQTT

These days I’m playing with IoT. Today I want to use MQTT protocol to comunicate between different devices. First I’ve start a mqtt broker in my Laptop. For testing I’ll use mosquitto server. In production we can use RabbitMQ or even a 3party server such as iot.eclipse.org or even Amazon’s IoT service.

The idea is emit one value with one device, and listen this value whit the rest of devices and perform one action depending on that value. For example I will use one potentiometer connected to on NodeMcu micro controller.

This controller will connect to the mqtt broker and will emit the value of the potentiometer (reading the analog input) into one topic (called “potentiometer”). We can code our NodeMcu with Lua but I’m more confortable with C++ and Arduino IDE. First I need to connect to my Wifi and then connect to broker and start emmiting potentiometer’s values

#include <PubSubClient.h>
#include <ESP8266WiFi.h>

// Wifi configuration
const char* ssid = "MY_WIFI_SSID";
const char* password = "my_wifi_password";

// mqtt configuration
const char* server = "192.168.1.104";
const char* topic = "potentiometer";
const char* clientName = "com.gonzalo123.nodemcu";

int value;
int percent;
String payload;

WiFiClient wifiClient;
PubSubClient client(wifiClient);

void wifiConnect() {
  Serial.println();
  Serial.print("Connecting to ");
  Serial.println(ssid);

  WiFi.begin(ssid, password);

  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.print("WiFi connected.");
  Serial.print("IP address: ");
  Serial.println(WiFi.localIP());

  if (client.connect(clientName)) {
    Serial.print("Connected to MQTT broker at ");
    Serial.print(server);
    Serial.print(" as ");
    Serial.println(clientName);
    Serial.print("Topic is: ");
    Serial.println(topic);
  }
  else {
    Serial.println("MQTT connect failed");
    Serial.println("Will reset and try again...");
    abort();
  }
}

void mqttReConnect() {
  while (!client.connected()) {
    Serial.print("Attempting MQTT connection...");
    // Attempt to connect
    if (client.connect(clientName)) {
      Serial.println("connected");
      client.subscribe(topic);
    } else {
      Serial.print("failed, rc=");
      Serial.print(client.state());
      Serial.println(" try again in 5 seconds");
      delay(5000);
    }
  }
}

void setup() {
  Serial.begin(9600);
  client.setServer(server, 1883);
  wifiConnect();
  delay(10);
}

void loop() {
  value = analogRead(A0);
  percent = (int) ((value * 100) / 1010);
  payload = (String) percent;
  if (client.connected()) {
    if (client.publish(topic, (char*) payload.c_str())) {
      Serial.print("Publish ok (");
      Serial.print(payload);
      Serial.println(")");
    } else {
      Serial.println("Publish failed");
    }
  } else {
    mqttReConnect();
  }

  delay(200);
}

Now we will use another Arduino (with a ethernet shield).

We’ll move one servomotor depending to NodeMcu’s potentiomenter value. This Arduino only needs to listen to MQTT’s topic and move the servo.

#include <SPI.h>
#include <Servo.h>
#include <Ethernet.h>
#include <PubSubClient.h>

#define SERVO_CONTROL 9
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };

Servo servo;
EthernetClient ethClient;

// mqtt configuration
const char* server = "192.168.1.104";
const char* topic = "potentiometer";
const char* clientName = "com.gonzalo123.arduino";

PubSubClient client(ethClient);

void callback(char* topic, byte* payload, unsigned int length) {
  Serial.print("Message arrived [");
  Serial.print(topic);
  Serial.print("] angle:");

  String data;
  for (int i = 0; i < length; i++) {
    data += (char)payload[i];
  }

  double angle = ((data.toInt() * 180) / 100);
  constrain(angle, 0, 180);
  servo.write((int) angle);
  Serial.println((int) angle);
}

void mqttReConnect() {
  while (!client.connected()) {
    Serial.print("Attempting MQTT connection...");
    // Attempt to connect
    if (client.connect(clientName)) {
      Serial.println("connected");
      client.subscribe(topic);
    } else {
      Serial.print("failed, rc=");
      Serial.print(client.state());
      Serial.println(" try again in 5 seconds");
      delay(5000);
    }
  }
}

void setup()
{
  Serial.begin(9600);
  client.setServer(server, 1883);
  client.setCallback(callback);
  servo.attach(SERVO_CONTROL);
  if (Ethernet.begin(mac) == 0) {
    Serial.println("Failed to configure Ethernet using DHCP");
  }

  delay(1500); // Allow the hardware to sort itself out
}

void loop()
{
  if (!client.connected()) {
    mqttReConnect();
  }
  client.loop();
}

Finally we’ll use one Raspberry Pi with a Sense Hat and we’ll display with its led matrix different colors and dots, depending on the NodeMcu’s value. In the same way than the Arduino script here we only need to listen to the broker’s topic and perform the actions with the sense hat. Now with Python

import paho.mqtt.client as mqtt
from sense_hat import SenseHat

sense = SenseHat()
sense.clear()
mqttServer = "192.168.1.104"

red = [255, 0, 0]
green = [0, 255, 0]
yellow = [255, 255, 0]
black = [0, 0, 0]

def on_connect(client, userdata, rc):
    print("Connected!")
    client.subscribe("potentiometer")

def on_message(client, userdata, msg):
    value = (64 * int(msg.payload)) / 100
    O = black
    if value < 21:
        X = red
    elif value < 42:
        X = yellow
    else:
        X = green

    sense.set_pixels(([X] * value) + ([O] * (64 - value)))

client = mqtt.Client()
client.on_connect = on_connect
client.on_message = on_message

client.connect(mqttServer, 1883, 60)
client.loop_forever()

The hardware:

  • 1 Arduino Uno
  • 1 NodeMCU (V3)
  • 1 potentiometer
  • 1 Servo (SG90)
  • 1 Raspberry Pi 3 (with a Sense Hat)
    • Source code is available in my github.

NFC tag reader with Arduino

Today I want to use the NFC tag reader module with my Arduino. The idea is build a simple prototype to read NFC tags and validate them against a remote server (for example a node tcp server). Depending on the tag we’ll trigger one digital output or another. In the example we’ll connect leds to those outputs, but in the real life we can open door or something similar.

We’ll use a MFRC522 module. It’s a cheap Mifare RFID/NFC tag reader and writer.

MFRC522 Connection:

  • sda: 10 (*) -> 8
  • sck: 13
  • Mosi: 11
  • Miso: 12
  • Rq: —
  • Gnd: Gnd
  • Rst: 9
  • 3.3V: 3.3V

In this example we’ll use a ethernet shield to connect our Arduino board to the LAN. We must take care with it. If we use ethernet shield with a MFRC522 there’s a SPI conflict (due to ethernet shield’s SD card reader). We need to use another SDA pin (here I’m using pin 8 instead of 10) and disable w5100 SPI before configure ethernet.

// disable w5100 SPI
pinMode(10, OUTPUT);
digitalWrite(10, HIGH);

Here is the Arduino code

#include <SPI.h>
#include <MFRC522.h>
#include <Ethernet.h>
#include <EthernetClient.h>

#define RST_PIN 9
#define SS_PIN  8
#define ERROR_PIN 7
#define OPEN_PIN 6
#define OPEN_DELAY 2000

char server[] = "192.168.1.104";
int port = 28001;

signed long timeout;

byte mac[] = { 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };
MFRC522 mfrc522(SS_PIN, RST_PIN);
EthernetClient client;

void printArray(byte *buffer, byte bufferSize) {
  for (byte i = 0; i < bufferSize; i++) {
    Serial.print(buffer[i] < 0x10 ? " 0" : " ");
    Serial.print(buffer[i], HEX);
  }
}

String dump_byte_array(byte *buffer, byte bufferSize) {
          String out = "";
    for (byte i = 0; i < bufferSize; i++) {
        out += String(buffer[i] < 0x10 ? " 0" : " ") + String(buffer[i], HEX);
    }
    out.toUpperCase();
    out.replace(" ", "");
    
    return out;
}

void resetLeds() {
  digitalWrite(OPEN_PIN, LOW);
  digitalWrite(ERROR_PIN, LOW);
}

void open() {
  Serial.println("OPEN!");
  digitalWrite(OPEN_PIN, HIGH);
  delay(OPEN_DELAY);
  digitalWrite(OPEN_PIN, LOW);
}

void error() {
  Serial.println("ERROR!");
  digitalWrite(ERROR_PIN, HIGH);
  delay(OPEN_DELAY);
  digitalWrite(ERROR_PIN, LOW);
}

void scanCard() {
  byte status;
  byte buffer[18];
  int err = 0;
  byte size = sizeof(buffer);
  EthernetClient c;
      
  if (mfrc522.PICC_IsNewCardPresent()) {
    if (mfrc522.PICC_ReadCardSerial()) {
      const String ID = dump_byte_array(mfrc522.uid.uidByte, mfrc522.uid.size);
      Serial.println("New tag read: " + ID);
      mfrc522.PICC_HaltA();
     
      if (client.connect(server, port)) {
        timeout = millis() + 3000;
        client.println("OPEN:" + ID);
        delay(10);

        while(client.available() == 0) {
          if (timeout - millis() < 1000) {
              error();
              goto close;
          }
        } 
        int size;
        bool status;
        
        while((size = client.available()) > 0) {
          uint8_t* msg = (uint8_t*)malloc(size);
          size = client.read(msg,size);
          //Serial.write(msg, size);
          // 4F4B   -> OK
          // 4E4F4B -> NOK
          status = dump_byte_array(msg, size) == "4F4B";
          free(msg);
        }
        
        Serial.println(status ? "OK!" : "NOK!");
        if (status) {
          open();
        } else {
          error();
        }
close:
        client.stop();
      } else {
        Serial.println("Connection Error");
        error();
      }
    }
  }
}

void setup()
{
  resetLeds();
  Serial.begin(9600);
  Serial.println("Setup ...");

  // disable w5100 SPI
  pinMode(10, OUTPUT);
  digitalWrite(10, HIGH);

  SPI.begin();
  mfrc522.PCD_Init();

  if (Ethernet.begin(mac) == 0) {
    Serial.println("DHCP Error");
    error();
    while (true) {}
  }
  Serial.print("My IP: ");
  for (byte B = 0; B < 4; B++) {
    Serial.print(Ethernet.localIP()[B], DEC);
    Serial.print(".");
  }
  Serial.println();
  Serial.println("Finish setup");
  timeout = 0;
}

void loop()
{
  resetLeds();
  scanCard();
  delay(200);
}

Now we only need to create a simple tcp server with node to validate our NFC tags.

var net = require('net');

var LOCAL_PORT = 28001;
var validTags = ['X3C86AD9'];

var validateTag = function(tag) {
    return validTags.indexOf(tag) > -1;
};

var server = net.createServer(function (socket) {
    console.log(socket.remoteAddress + ":" + socket.remotePort);
    socket.on('data', function(msg) {
        var out;
        [action, tag] = msg.toString().toUpperCase().trim().split(":");
        console.log(action, tag);
        switch (action) {
            case 'OPEN':
                out = validateTag(tag) ? "OK" : "NOK";
                console.log(out);
                socket.write(out);
                break;
            default:
                console.log("unknown action:", action);
        }

        socket.destroy();
    });
});

server.listen(LOCAL_PORT, '0.0.0.0');

And that’s all. Here a video with the working example

And full code available in my github account.

References about rfid and Arduino: here, here and here